November 2018 – Thanksgiving weekend run in Albany NY at the Palace Theatre

Designed by Nathaniel Deas and screenprinted on olive green tees

Fully sublimated polyester fabric shower curtain measures 72″ x 72″

Featuring custom, original art from a painting by Gwen AP.

Estimated ship date Dec 17

Custom knit-in logo jaquard dress socks. 

Choice of two colors – maroon or blue

Anticipated ship date 12/19 – cannot guarantee delivery by Xmas Eve.

Art by Stacey Ratcliff

This is a preorder expected to ship the week of 12/3

This high-quality, lightweight zip-up water-resistant windbreaker features embroidered logo front left chest.

Your choice of two colors, black/gray or black/camo.

Jacket specs:

• 82 Gm 100% polyester fabric with interior water resistant coating
• matte finish eyelets and zippers
• three panel hood with fine mesh liner
• scuba neck with self neck tape
• welt pockets with mesh pocket bags
• tightening toggle at waistband
• elastic cuffs
• locker loop in center back

Silicone cell phone wallet hold cards and cash, and bends to serve as a phone stand.

Black with white imprint.

Embroidered gold Disco Biscuits crest on the front left chest. Choice of black or purple robe.

Made of 100% microfiber polyester fleece fabric, this is THE most luxurious fleece robe available.

• One Size
• 48” long
• 2 patch pockets
• 100% microfiber polyester

High-quality, sublimated full-color all-over print ladies leggings.

Full length leggings with comfortable waistband.

Heavyweight black zip up hoodie.

Glow in the dark back print art

Design by Christian Jaxheimer.

High-quality nylon water-resistant windbreaker anorak jacket features an embroidered logo on the right shoulder, and the screenprinted band name on the pouch pocket.

Choice of two colors, navy or black. Please note backordered sizes on Black: small, large and XL.

The nylon exterior fabric of the jacket is coated with a 100% waterproof coating; seams are highly water resistant but not waterproof.

• 100% nylon 330D with Interior PU waterproof coating
• matte metal zipper pull with rubber zipper pull tab
• 3 panel hood with fine mesh hood liner
• matte nickel metal eyelets and round poly drawstring
• scuba neck
• hidden snaps inside front pocket flap
• side slit pockets
• tightening toggle at waistband
• elastic cuffs

Pullover hoodies printed on super soft special blend navy blue hoodies, with colorful blue and pink logo screenprinted on the front, geometric medallion panther on the back, and THE DISCO BISCUITS down the right sleeve.

Design by Christian Jaxheimer.

This 6″ Snowboard Stomp pad protect assists riders when getting off of chair lifts. Mounted between the bindings, stomp pads are used to secure the rear foot when getting off of a chair lift at the top of the mountain. All pads come with high performance adhesive for secure mounting to the board by the recipient. Logo is protected under the clear material of the pad, which provides traction for keeping the rear foot in position.

INSTALLATION INSTRUCTIONS:

You want to install your stomp pad as close to your back binding as you can – this will make it feel as close to your normal stance as you can make it. And it will also mean that you can lean your boot against the binding for extra stability.

Make sure that you position the stomp pad on the inside of the back binding.

Here’s how to find the best spot for your stomp pad.

1. Place your snowboard on the ground and put your boots on
2. Place your back foot on the snowboard on the inside of the back binding, close to the back binding so that you are still standing upright and so that the side of your boot is touching the side of the binding
3. Mark the points on the board where the inside and outside of your boots touch the board
4. When you place your stomp pad it should be inside these tape marks (or at least not outside the tape mark that’s next to the binding)

Installing the stomp pad

Now you have the position of your stomp pad it’s time to install it/them

1. Thoroughly clean and dry the area of your board where you will be placing the stomp pad/s. If you try to attach them to a dusty, unclean or wet surface they may lose their stick quickly
2. To ensure the best possible stick make sure that you are in a warm room or heat up the boards surface with a hair dryer
3. Remove the backing to expose the adhesive and place on your stomp pad.
4. Then remove the other side of adhesive and place the stomp pad in the position you marked earlier. Press down as hard as possible and hold the pad in place for a while.
5. Let the adhesive dry for 24 hours.

1/4″ thick acrylic magnet with full color design

Design by Christian Jaxheimer

Knit winter hat with cuffed brim and pom. Knit-in logo design.

This item will begin shipping 11/29