Screen printed across the back and left chest

Art by Mark Serlo

NEW Summer 2019 Hoodie

Screenprinted across the front and down both sleeves

Design by Taylor Morgan

Handmade coaster with original Disco Biscuits design by Julie Nuzzo. Very limited quantities on hand!

NEWflatbrim hat with black 6-panel cap, black and white hawaiian tropical pattern brim and a snapback.  Embroidered white round logo front and center.

Hat specs:

100% Cotton

Structured

Firm Front Panel

• 6 panel cap
• Seamed front panel with full buckram
• 6 sewn eyelets
• 8 Rows Stitching on Visor
• Matching Fabric Undervisor
• Plastic Adjustable Snap Closure

NEW flatbrim hat with digital camo 6-panel cap, black brim and snapback.  Embroidered coordinating green round logo front left panel.

Hat specs:

100% Cotton

Structured Cap

Firm Front Panel

• 6 panel cap with 6 sewn eyelets
• Seamed front panel with full buckram
• 8 rows stitching on visor
• Matching fabric undervisor
• Plastic snap closure

Ladies fit black glitter french terry pullover hoodies – yes glitter hoodies! With large Disco Biscuits round logo in shiny foil print across the front.

Fabric is:  55% cotton, 25% lurex, 20% polyester French terry

Size chart:

Colorful woven throw blanket designed by Nic Bogdall

Blankets measures appx 5×8 feet or the size of a full size bed. Fringed top and bottom. Made in the USA.

Fully sublimated polyester fabric shower curtain measures 72″ x 72″

Featuring custom, original art from a painting by Gwen AP.

Estimated ship date Dec 17

This is a preorder expected to ship the week of 12/3

This high-quality, lightweight zip-up water-resistant windbreaker features embroidered logo front left chest.

Your choice of two colors, black/gray or black/camo.

Jacket specs:

• 82 Gm 100% polyester fabric with interior water resistant coating
• matte finish eyelets and zippers
• three panel hood with fine mesh liner
• scuba neck with self neck tape
• welt pockets with mesh pocket bags
• tightening toggle at waistband
• elastic cuffs
• locker loop in center back

Silicone cell phone wallet hold cards and cash, and bends to serve as a phone stand.

Black with white imprint.

Welcome to your new favorite hoodie, ladies.  This long length hoodie dress is screenprinted across the chest with the band name and embroidered on the pocket with the round Disco Biscuits logo.

Created for comfort using an exclusive Special Blend fabric and a stylish silhouette, this hoodie provides the ultimate in cozy coverage. Features include a crossover neck, thumbholes, and 2 drawcords in contrasting colors.

Size chart in additional photos.

High-quality, sublimated full-color all-over print ladies leggings.

Full length leggings with comfortable waistband.

Heavyweight black zip up hoodie.

Glow in the dark back print art

Design by Christian Jaxheimer.

This 6″ Snowboard Stomp pad protect assists riders when getting off of chair lifts. Mounted between the bindings, stomp pads are used to secure the rear foot when getting off of a chair lift at the top of the mountain. All pads come with high performance adhesive for secure mounting to the board by the recipient. Logo is protected under the clear material of the pad, which provides traction for keeping the rear foot in position.

INSTALLATION INSTRUCTIONS:

You want to install your stomp pad as close to your back binding as you can – this will make it feel as close to your normal stance as you can make it. And it will also mean that you can lean your boot against the binding for extra stability.

Make sure that you position the stomp pad on the inside of the back binding.

Here’s how to find the best spot for your stomp pad.

1. Place your snowboard on the ground and put your boots on
2. Place your back foot on the snowboard on the inside of the back binding, close to the back binding so that you are still standing upright and so that the side of your boot is touching the side of the binding
3. Mark the points on the board where the inside and outside of your boots touch the board
4. When you place your stomp pad it should be inside these tape marks (or at least not outside the tape mark that’s next to the binding)

Installing the stomp pad

Now you have the position of your stomp pad it’s time to install it/them

1. Thoroughly clean and dry the area of your board where you will be placing the stomp pad/s. If you try to attach them to a dusty, unclean or wet surface they may lose their stick quickly
2. To ensure the best possible stick make sure that you are in a warm room or heat up the boards surface with a hair dryer
3. Remove the backing to expose the adhesive and place on your stomp pad.
4. Then remove the other side of adhesive and place the stomp pad in the position you marked earlier. Press down as hard as possible and hold the pad in place for a while.
5. Let the adhesive dry for 24 hours.

1/4″ thick acrylic magnet with full color design

Design by Christian Jaxheimer

Sublimated fabric mini tapestry with grommets in corners. Measures 30″ x 30″.

Art by Christian Jaxheimer – First Earth

Above the Waves logo design by Zack Katz

Screenprinted across the front of navy/baby blue ladies fit baby rib raglan baseball tees with 3/4 length sleeves

Garment is 100% cotton. Size chart in inches:

Colorful hot air balloon design logo screenprinted in full with additional print on the back featuring band name.

Design by Dima Yastronaut.

100% cotton shirt is hand dyes in shades of blue, purple, green and yellow